You most certainly can! With the use of RaceROM Custom Maps you can make calibrations in different Map Switch modes for pure E85 or E70 fuel (no mix ratios though). For true Ethanol tuning flexibility you can fit and import the Zeitronic Flex-Fuel sensor and import the Zeitronic signal into the factory ECU.
By setting up Custom Maps it’s possible to turn the BRZ/GT86/FR-S into a true Flex-Fuel vehicle. Expect around a 20-25bhp increase in power, but be aware that you will use 25-35% more fuel.
Yes, Launch Control, Flat-Foot Shift and Autoblip are all configurable in any of the four modes, along with Speed Density. Four-way Map Switching is only available to trade customers or retail customers who have purchased the optional RaceROM BRZ upgrade package.
Yes, ensure your tune is based on the latest RaceROM Feature File and the Map Switch mode will be remembered (although older RRFF versions may not be able to retain the current Map Switch mode).
Correct, the cranking fuelling is calculated from the MAP sensor, so you MUST correctly re-scale the sensor before trying to start the car. You also need to alter the DTC limits for the MAP sensor voltage range.
Yes, you can enable or disable SD in any of the four modes. You can also use the Hybrid SD function in any or all of the four Map Switch modes.
Yes, simply flash the 100% standard factory ROM file back into the ECU; this will allow other tuning tools access to re-flash the ECU, and the ECU will appear standard to the dealer.
Yes, to return the CVN to original the ECU must be flashed back to standard.
No, the dealer re-flash tool (or other tuning tools) cannot over flash the ProECU tuned ROM; the ECU must first be flashed back to standard.
In the event that the ECU programming sequence fails (such as if laptop power dies or the vehicle interface becomes disconnected) don’t worry, as ProECU can recover the ECU. The normal procedure of using Tools → Detect Vehicle will not work at this point and you will need to click Tools → Manually Select Vehicle → Subaru BRZ/Toyota FT-86 → Program Engine ECU.
It is vital that you select the correct vehicle type, and once on the programming tool window, you must choose a 100% standard ROM file for the recovery sequence to work as expected. After successfully programming the ECU with a 100% standard ROM file you can subsequently program a tuned ROM file.
There are a number of possible reasons:
If you hit the maximum 5V you will get a MAF Fail Safe condition based on MAP sensor calculation and P0103 DTC. This Fail Safe condition will occur even if you are running full-time SD, so ensure P0103 is disabled so that the MAF hitting 5V does not cause any issues.
If your DI open time period is too long then the DI could still be open when the spark plug fires; check the logging parameter called Fuel Injection End DI to Spark (ms) to see what time period is left.
If you have a retail programming kit you will need to purchase the RaceROM BRZ product update from your Master Tuner.
Yes, ProECU can open any Tuned or Stage xxx ROM files that are available on the various internet forums. The ROM file will need to be 1280KB in size and the file name extension may need to be changed to .bin for ProECU to open the raw ROM (because many free files are labelled as .hex or .org or .rom).
Yes, you can replace the Carbon Purge Canister solenoid valve with a conventional wastegate solenoid. You can then use Custom Maps to control the CPC valve, which can be used in a closed loop or with open-loop boost control. You should also alter the valve frequency to suit your chosen wastegate solenoid characteristics.
The throttle opening angle is relative to a base demand opening angle for idle and other functions. When you see the throttle angle reducing its actually because the base airflow demand is increasing with RPM while the physical angle stays the same. When you look at TPS Voltage it is actually holding the same opening voltage so is not moving. Try logging these parameters and see what moves if you think you have an issue.
One important thing to look out for when tuning BRZ/FT/GT86's is that the VVT is enabling, you will be down on power and the MAF / SD mapping will be different depending on whether the cams are active or not. There is a new parameter for VVT enabled that can show if they are active or not and you should wait for the parameter to go to 1 before the power run. You will need to follow some simple rules to make VVT activation much more straightforward. Your workflow should be something like this:
That works on our car with CALID ZA1JA01G 100% of the time. If you don't do the drive-stop cycle you could be there for a long time. Below is a screenshot showing that parameter and how the VVT turns on after the drive-stop cycle.
The car can disable cam timing if it isn't seeing the movement requested due to oil level, so ensure your car (as usual) has enough oil. |
Some cars on hub dyno's do not like to activate the cams and while we don't know the exact cause there are some hints and tips that may help below
Due to the complexity of the BRZ/GT86/FR-S fueling strategy and the evolving OEM methodology we currently can only overwrite the Base Map target AFR values. If you wish to use the Target AFR adjustment in custom maps in an MY17+ car with Power AFR maps you will have to use the exhaust temperature threshold to force the strategy into using the Base AFR target maps more often or full time and create your own Power AFR custom map (if you want this functionality). The lean Closed loop AFR target map cannot be overwritten currently.