OBD Unlock Tool
Introduction
This guide refers specifically to EcuTek OBD unlocking using the ProECU software on a PC ,carried out in the car, it is a different process to bench unlocking, or using PhoneFlash.
Before being able to flash an EcuTek tuned rom onto the vehicle, the ECU must first be EcuTek unlocked. This process is only required when dealing with a ECU which is completely stock, or has been “unlocked” for programming by a third party tool such as bFlash, Autotuner, Femto etc, or has been returned to completely stock had any EcuTek licenses removed and “relocked”.
ECUs that have been “unlocked” by other tools, including post 2020 unlocking still need to go through the EcuTek unlock process before programming an EcuTek tuned ROM file.
EcuTek OBD unlocking allows programming of non-OEM ROM files, adds EcuTek licencing information, will flash the stock calibration, and will save a copy of the coding to the PC for later use.
To perform an EcuTek unlock of post June 2020 ECUs that have been “fully” unlocked by Autotuner, Ceky, Femtoevo etc use the option here
Unlocking is similar across all EcuTek BMW platforms, the General workflow for unlocking the ECU before tuning is as follows.
Preparing for unlocking
Ensure laptop that has sufficient battery charge to last the unlock process.
The car battery will also need to be in good condition
Lights, blower, ICE switched OFF!
If in any doubt you may want to use a low current battery charger on the car
Make sure to leave the key in the car while the process is happening and avoid any additional unnecessary draws on the electrical system.
Use of a battery charger on the vehicle while your computer is plugged into the vehicle for power can cause damage to the computer or the vehicle's ECU. It's recommended to run the computer off of battery or a power source outside of the vehicle.
Getting Connected
Step 1: Connect EcuTek Interface cable to USB port of PC and OBD port start ProECU
Step 2: Detect or Manually select vehicle or ECU
Turn the ignition on, in most BMW vehicles this requires diagnostic mode, using 3 presses of the ignition button to fully power the car up.
Click on “Detect Vehicle” from the “Tools” pulldown menu, or using the F3 to start automatic detection of the vehicle type.
In some rare cases ProECU may not correctly detect the vehicle, in which case it may be necessary to manually select the vehicle type.
Select the vehicle which matches the target vehicle being unlocked.
Open the Unlock Tool
After the vehicle or ECU is detected or selected, the next step is chosen, the default option is set to "Program Engine ECU" but if connecting to unlock the ECU select "ECU Unlock Tool":
The Unlock Process
Once the ECU unlock tool has opened, click on "Query ECU" and the ECU will be detected, and its components reported:
Choose the Unlock action
Unlock and licence a stock ECU that has not previously been tuned
Use this for ECUs which should be OBD unlockable, but are completely stock. This includes most N55/S55 cars, most 1st generation B58 cars and some early 2018/2019 2nd generation B58 cars. However many cars that were originally OBD unlockable at time of sale, will have had dealer updates that mean they cannot be OBD unlocked and now require bench unlocking.
It is safe to try this option if you are unsure.
Put an EcuTek License into an ECU that is already unlocked and/or tuned
Use this option for ECUs that have been bench unlocked by a tool other than ProECU (ProECU supports native bench unlocking and licensing in one operation using a bFlash device or EcuTek Bench Programmer.
If the car being tuned has previously been OBD unlocked by another tool, ProECU will still need to go through an EcuTek unlock process to program the license information and additional code into the bootloader portion of the ROM.
If your ECU was manufactured after Jun 2020 and has been shipped to Autotuner, FemtoEvo or similar, this is the option you need.
Upgrade an unlock ECU and licenced ECU to a newer rom version
If the ECU has already been EcuTek unlocked and licensed, but there is an updated version of the BMW software, this option allows updating, even if the bootloader has been updated too.
ROM versions can only be upgrading via OBD, downgrading requires bench programming
Flash a stock ROM into the ECU (relock and remove EcuTek license)
If you want to return the ECU to 100% stock condition, choose this option. Do not choose this option if you simply want a stock calibration, it is not required to relock an ECU just to program a stock calibration without RaceROM.
This action will reinstate full OEM programming protection, and may require bench unlocking of the OEM rom cannot be OBD unlocked.
Autotuner unlocked 06/2020 and later ECUs will required Autotuner bench unlocking using a normal Autotuner tool before tuning again
Start Unlock
Click on "Start" and you will be prompted to select a 100% unmodified ROM file. The dialog box will be prefilled with the correct ROM (although some of the name is obscured when the file dialog pops up), you should be able to click on "Open" or just hit the "Enter" key.
If the file is successfully loaded, the progress window will be updated, and the licence status will be reported:
You are now ready to proceed with the unlock process. Click on "Unlock ECU" and progress will begin. This typically takes around 9 minutes, it is normal for the low pressure fuel pump to run on some cars.
Conclude unlocking
When the unlock process is complete the ECU will be reset and DTCs cleared. Cycle the ignition by turning off for a few seconds and then back on to restart all the other modules on the car.
If the ECU is unresponsive, or the car will not start, make sure to cleanly return the ECU to normal operation by clicking on the “Exit Programming Mode” button.
ECU Unlock Troubleshooting
Your current ECU must be supported within ProECU before you can unlock it, check you are running the latest ProECU if your ECU is not currently supported. If it is still not supported, they you must use the “Dump ECU for EcuTek” to read the stock rom and send it to ECU so we can add support.
In some cases, it may be necessary to do a second vehicle-wide clear DTC operation after the ECU unlock process and/or an additional ignition power cycle.
If for whatever reason unlocking is interrupted or fails, it should be possible to restart the process without issue.
After an unlock failure, it is possible the ECU is partly blank and will not communicate using normal OBD commands, thus the vehicle cannot be detected. If you close and re-open ProECU for whatever reason (eg laptop ran out of battery) you will need to manually select the vehicle, do not rely on autodetect.
If restarting an unsuccessful ECU unlock operation, it is possible (but rare) the ECU will have been left without an EcuTek licence. If this should occur, please use an additional license and contact EcuTek support to get your licence points balance corrected.