RE7R Tuning Guide

RE7R Tuning Guide

Overview

Tuning the RE7R gearbox requires understanding some fundamentals about how the control structure is applied. Our understanding is based on reverse engineering of the strategy and correlation to the workshop manuals. The key points are

Identifying the transmission type you have

If you are trying to identify a 7-speed TCM in a Nissan that does not have the programming window in the select tuning tools drop-down, go to Tools → Manually Select Single ECU..

image-20250626-094903.png

and choose Nissan 370Z/VR30TT 2016 -> TCM

image-20250626-094834.png

From here, you can select the Program Transmission ECU option and start ROM dumps or programming.

image-20250626-095040.png

If you have a type 1 (m32) TCM, you can still dump the ROM (we encourage it) so that we can add it for maps-only support soon.

To identify a TCM type when its removed from the vehicle the following has been found to apply

M32R type part numbers

  • M3B ETC94-110N

image-20250813-161848.png

SH type Part Numbers

  • G2A ETC96-200N

image-20250813-162019.png

Adding Support and ROM Dumps

TCMs must be added for support before any programming and tuning can be performed to dump a ROM query the vehicle and select the correct programming window (as above). ROM additions are handled via the standard ROM addition procedure. Two types of dumps can be made: a calibration-only dump and a FULL rom dump. ProECU will first attempt a full dump; if this is unsuccessful, it will try to create a calibration-only dump.

A full dump may be required to complete ROM addition. If this is the case, wiring into the CAN bus as close to the TCM as possible will be required. This can be done by connecting to any point in the CAN bus on the other side of the gateway, such as at the ABS plug (by unplugging the ABS module and plugging into the can pins).

Wiring (at TCM)

image-20250729-163912.png

Wiring (at ABS Module)

image-20250815-150154.png
image-20250815-150345.png

There is an older type of ABS module in 370z’s etc that has a different connector, the process is the same though just with a different pinout

image-20250929-160158.png

 

Programming

To program a TCM, you will need to be connected to the OBD port, and the CAL ID must be recognised and added for support.

image-20250626-094523.png

From there, select Program Transmission ECU and press the dump details for EcuTek as you usually would when adding an unrecognized ECU.

CAL ID Changes

The RE7R SH type processor has some cross compatibility but changing cal ID’s has be known to brick TCU’s completely, EcuTek have tested as thoroughly as possible but cannot guarantee cross flash compatibility.

Some CAL IDs may have more desirable configurations for shift schedule maps or shift speeds, it is recommended that checks and tests be performed before changing cal id.

Swapping TCM Controllers

M32R type gearbox controllers have been swapped for SH types in some vehicles without issues, to find an SH type TCM. It appears that they mount the same and connect the same to the valve body and solenoids. We do not know if they are 100% compatible so swap controllers with caution.

Torque Controls

  • There are two types of torque control.

    • Fast Type (for ignition and fuel cut) logged as Torque reduction 1 in the ECM.

    • Slow Type (for throttle and boost target) logged as Torque reduction 2 in the ECM.

  • There appear to be two modes of torque control,

    • Static torque, which is the maximum allowable torque while in a gear

    • Dynamic torque, which is the torque control for gear shift and other transient behaviours like stopping.

Clutch and Brake Pressures

Clutch and brake pressure targets are derived from torque targets using conversion factors in the solenoid gain and offset. The converted values are then referenced in the solenoid scaling maps to output solenoid current targets, which are then transferred into a solenoid duty and output to the solenoid physically.

  • Two types of solenoids are used to control the clutch/Brake

    • Normal Hi (increasing current to increase pressure)

    • Normally Low (reducing current to Increase Pressure)

  • There are three separate sets of pressure targets

    • Static Pressure Targets

    • Incoming clutch Pressure targets

    • Outgoing Clutch Pressure targets

  • Solenoid Control

    • There is a target current value and an actual current amount, each with global limits.

    • These targets are NOT independently controlled (meaning you can't specify each clutch/brakes limit without affecting others).

Shift Schedules and Modes

  • There are several shift schedule arrays, which are used under different circumstances, some of which are currently unknown.

  • Shift arrays are Split between manual and drive shifter positions

  • Each mode is split into Normal, Sports, Eco, Snow and a transient set

  • High and low accel pedal thresholds are paired above and below which a shift change is triggered

Logging

The OEM TCM OBD logging is returned in a group, so little speed advantages are found by unselecting parameters. There are RaceROM logging parameters available to aid you in tuning shift points, target pressures and torque limits; these are available as soon as a RR patch is applied.

image-20250626-111952.png

Recovery

If issues arise when programming the TCM, there are two modes of recovery: the normal recovery for part-programmed ECUs. If there is an issue with the calibration that stops the TCM from running, RaceROM has a separate mode of recovery which can be used. Contact support@ecutek.com if you need to recover a TCM from bad calibration data.

Moving the car when in recovery mode

To unlock the TCM if you are stuck in recovery mode you can

  1. remove the cover

    image-20250813-161240.png
  2. Use a screwdriver to release the shift lever and put the shifter into neutral.

Tuning

MAP lists and Types

The Re7R calibration offers a wide range of map types and formats, including 1D, 2D, 3D, 4D, and variations of 2D with included hysteresis (displayed as 3D). Due to limitations of ProECU, some of the 3D maps may have axis values that will not be used like a simple map lookup.

image-20250626-112121.png

For example, the solenoid scaling maps have pressure target as input, solenoid current target as output and then the final calculated output limit value as the second column. There are a few types of maps like this, so use caution when changing maps.

image-20250626-114619.png

4D maps are displayed in a similar method to Toyota, where we have a series of 3D maps for each position on the 4th axis, so a 3D map per 4th dimension bin

image-20250626-115425.png

Torque Control and Limits

Torque limits from the TCM are sent to the ECM via CAN. The TCM receives the torque actual over CAN, which it uses to set pressure targets and shift speeds. The TCM also use accel/throttle pedal values over CAN to deliver shift points and blip requests.

Torque Logging

The Torque Demand and Torque Actual values calculated in the ECM and sent to the TCM are available for logging with the TCM, the torque reduction request values sent to the ECM can be from the TCM can also be logged. There are several parameters that

image-20250721-161638.png

Torque limits

The static Torque limit is the first thing to look at changing. For static torque limits, there are several maps, the primary control map being the Torque Limit 1 (Slow) map. This map features a gear axis and a vehicle speed state Y axis, where 1 corresponds to 0 km/hr vehicle speed, and 2-4 represent unknown vehicle speed states.

image-20250626-170230.png

There are alternative torque limits, and some platforms have more than 2 limit maps, which may also need adjusting. The Torque limit being output from the TCM can be logged using the torque limit parameter.

Torque Reduction Requests (Shift and Overrun)

The TCm has three modes/types for torque request applications:

 

Mode

Description / Function

Mode

Description / Function

0

Static (no gear change present)

1

Upshift (the gear requested is above the current gear)

2

Downshift (the gear requested is below the current gear)

Torque reduction request values are sent from the TCM to the ECM constantly. They are loggable in both the ECM and the TCM. There are two Torque Reduction outputs sent to the ECM,

  • Torque Reduction Request 1 - Fast path torque (ignition and fuel cut)

  • Torque Reduction Request 2 - Slow path (throttle and boost)

The TCM will make torque reduction requests when stationary, moving in specific gears, in overrun, during gearshift when the lever is moved or the brake is applied and when in limp modes. The torque reduction requests are generally made with a setpoint value and a ramp out; this ramp out can sometimes be ignored if the reduction isn’t required anymore.

There are

image-20250722-091445.png

Control of the amount of torque reduction during a gear shift will be added soon. It is understood that there are a series of modes that have 1D values as the limit, and finding these modes and how they are applied is yet to be reverse-engineered.

Shift Schedules / Shift Points

Shift schedule / shift point is the vehicle speed/rpm at which the TCM decides to request the next gear. The TCM uses vehicle speed to choose when to shift gears. This translates the gear ratio into RPM points, so increasing the vehicle speed for the same pedal position will increase the RPM at which the gearbox chooses to shift.

The shift schedule can be broken down into a pair of large arrays of shift maps for which each mode and gear chooses a different series of calibratable maps. The two primary modes are:

  1. Shift selector in Drive Position (D position on the selector)

  2. Shift Selector in Manual Position (in manual shift position or after paddle press)

Each of these main arrays of maps is then split up into a secondary set of shift maps for those specific Drive modes,

Drive Shifter Position - split into drive modes using the mode selector.

  • Normal mode

  • Eco mode

  • Snow mode

  • Sport Mode

  • Intermediate mode

Manual Shifter Position

  • Only one mode

image-20250722-094700.png

Each series of mode maps is then grouped per gear current and gear demanded in a 14 x 7 size array. The maps in unused categories are generally those from unattainable shifts (like 1->7).

Within the array, each gear has thresholds for vehicle speed and accelerator pedal, above which an increase or decrease of gear is allowed.

image-20250722-155802.png

The maps have vehicle speed as the input and accel as the output. The accel value gets compared to the current accel pedal value, and the choice of up or down shift is set based on this comparison.

image-20250722-160055.png

When plotted, the maps line up to give a window in which a down shift, no shift and an up shift will be triggered. It is believed that in drive position, it will reference both the current gear map sets and the next gear map sets to see if a shift is needed.

image-20250722-161539.png

It is also possible that in some running modes it does not use the requested gear as the input (as no shift request is made), instead it will use the bottom row of the mode-specific array. For example if DTC are present it will default to the first row of the manual position maps.

image-20250722-164753.png

The output of these maps is a vehicle speed, which is used to select an accel pedal amount to compare to the current pedal value to determine if an increase or decrease in gear desired is required.

There are logging parameters that may help determine which set of maps is being used. Shift map choice auto and shift map choice manual give one set of maps that are being reviewed. The numbers should match the help text in the shift schedule, but be aware that the other maps might be referenced as per the discussion above about limits and thresholds.

image-20250722-165403.png

In the log below, shift map 476 is referenced in 1st gear.

image-20250722-165541.png

Shift Limits

Shift limits in manual mode can be partially adjusted, currently if the OEM map is set as a default ignore type map forced upshifts cannot be set, if it has normal values the forced upshift can be adjusted.

image-20250722-165733.png

Increasing the shift limit map will allow the rev limit to be extended in 1st gear.

2nd Gear Launch

2nd gear launch can be achieved by setting a byte to allow paddle requests when stationary and setting the upshift limits in the ROM.

image-20250722-165932.png

Setting the accel threshold that prevents upshift below 13.2km/h will then allow you to shift into second gear in manual mode when stationary.

image-20250722-170015.png

Forced upshift in Manual Mode

Currently, a forced upshift in manual modes in any gear other than 1st is not possible. This is likely because the maps are configured to be ignored, and enabling this forced upshift would require the addition of RaceROM maps. It has been noted that some EU ROMs can do this in all gears, and if they are read and dumped, the settings may be copied and enabled in other ROMs.

Another running mode can be used and configured to set no upshifts until the rev limit if required.

Shift Rate / Shift Times

Shift rates are controlled by gear ratio change in closed loop by the ECU. Current targets and delays have not been reverse-engineered, and further work will continue on this soon.

Pressure Control

Line Pressure Target

The line pressure of the gearbox is the pressure that is used to drive all of the hydraulic circuits in the gearbox. If there is insufficient line pressure all of the downstream control will also be effected. There are several line pressure target maps all of which can be tuned and are used under various running conditions.

image-20250805-172212.png

 

Torque for Line Pressure

The target line pressure is normally derived from torque from the ECM, however it does spike on transient behaviors. with high accel pedal delta or input torque delta (like gearshifts) the line pressure torque demand can be set using the LP torque conversion 1 map.

image-20250805-172720.png

This appears to help in setting the transient target higher and improving shifts.

It appears that the stable line pressure target 3D map is the use primarily and can be tuned to give a higher output if required

image-20250805-172312.png

Clutch / Brake Pressure Targets

Clutch / Brake pressure targets are used to set each clutch/brake pressure value and control how much torque is transferred when in gear (Stable/Static) and when changing gear (incoming and outgoing setpoints).

Stable gear static setpoints

When the gear is stable and the pressure targets are set to static values. To adjust the pressure targets when the clutch is locked and no gear change is active, adjust the 1D values that have a positive pressure target.

image-20250724-114056.png

Other maps with a target of 0 mean that they are set to 0 pressure target when in particular gears, allowing others to hold or transfer the torque. Adjusting these will only negatively affect the shift or possibly bind the clutches.

There are many other static target modes which have not yet been defined. If a target is not working as you expect, please contact support.

Mid Shift Targets / incoming and outgoing targets

Clutch pressure targets during clutch application or release are made using the gear ratio target. There are closed-loop control mechanisms to set these, which are not currently understood. Further development and map updates will be made in the near future to allow the shift speeds and pressures to be calibrated.

The Torque target applied during shifts could be as follows:

image-20250729-153022.png

Clutch / Brake Solenoid Current Controls

Solenoid currents, when in both stable/static pressure and Transient Pressure target modes, are controlled by pressure-to-amp scaling maps with hardcoded limits applied globally to all solenoids.

For example, suppose the converted clutch pressure target is above 22500. In that case, the function will choose a default amperage target of 800mA regardless of the scaling map output (shown below in the if statement). You can also see below that with lower targets, the pressure target to amps is not linear; this is likely because of the flow characteristics of the solenoids themselves at different currents (% duty).

Clutch Pressure targets simplified.png

Solenoid scaling maps should not need to be adjusted, and the output will always be limited to 800mA. Both columns of output values would need changing to keep the conversion smooth, which makes it difficult to achieve a controllable difference in current from pressure. There are global corrections for battery voltage and temperature that are applied to the amperage targets as well.

There is also closed-loop control of the amperage to a limited degree per clutch. These maps utilise a 2D map as the input axis for the 3D maps, which in turn use the Current Actual CL Correction value map output.

image-20250729-150103.png

The Clutch Current Ramp Rate Map 3D maps for closed-loop current control use the above correction factor and the clutch pressure target to decide a CL correction coefficient, which is then applied to the current target.

image-20250729-125953.png

Further down the chain, before conversion from current to solenoid duty, both battery voltage and temperature corrections are also applied.

image-20250729-150139.png
image-20250729-150210.png

 

Finally, the Current to duty conversion maps are applied. These are the values that are written to the solenoid outputs.

image-20250729-150041.png

 

Kick Down

To prevent kickdowns, the shift schedule can be adjusted so that at 100% pedal, the request is ignored until the rev limit is hit.

Torque Converter Clutch Lockup

Torque converter lockup has been shown to release after set torque values; this is prevented by increasing the max torque by one value.

Torque converter control is not yet disassembled, and hopefully, lockup points will be found and added for calibration soon.

Diagnostic Trouble Codes

Diagnostic trouble codes can be removed by unchecking the box. Care should be taken when disabling codes, as transmission issues should be addressed first to prevent further damage. Disabling a DTC may have unwanted side effects if the problem is not rectified first.

image-20250729-153448.png

Support and Tuning Assistance

For all EcuTek products, support can be obtained by email requests to support@ecutek.com. In urgent cases, phone calls can be made during work hours. Please submit a clear description of the issue, including the relevant ROMs and Logs, along with any tuning assistance requests. This will enable the support team to assist you in the most efficient way.