370Z CAN Input and Output
With Latest version of RaceROM CAN in and out are now available. For more information of setting up CAN in and out see the article here.
RaceROM CAN Sensor Input / Output
CAN Inputs / Outputs Devices
370Z has spare mailboxes available to send one CAN ID and recive one CAN ID of messages to and from external CAN equipped devices. This should allow either 2 separate devices as an independant input and output or one device that combines both input and output. Any CAN equipped module that has these defined input/outputs should be able to be used. for example devices such as
Motiv Reflex (ReFlex+ Control Unit - Nissan )
Total Racing Products CAN bus flex kits (Mission Control CAN bus version)
Syvecs OEX / tiny Dash (Syvecs TinyDash V2 - TouchScreen Syvecs OEX | (Oem Ecu eXpander) )
AMS CAN bus flex fuel kit AMS Performance INFINITI Q50/Q60 CAN Bus Flex Fuel Kit - AMS Performance
MaxxECU mini / PWM driver (MaxxECU MINI MaxxECU PWM module (kit) )
Visconti CANbox Pro (Visconti Tuning )
CAN Input / Output Wiring
Due to the primary CAN bus being fully utilized on the later model 370Z we have moved to use the VVEL CAN bus used to transmit VVEL messages from the Variable valve control module to the ECU. There are select points within the 370Z wiring loom that can be tapped into these are shown below.
NOTE: connector F5/6 is possibly only on Q50 models
Alternatively you can solder directly to the output pins at the base of the ECU header as we have done in this example.
Total Racing Products (TRP) Mission Control CAN Box
Total Racing Products Mission Control box is a CAN device that send Ethanol Content and Support Three Sensors to RaceROM further to this it can receive three PWM Outputs from RaceROM custom maps e.g. Boost Control, Trigger Relays, Control Brushless Pumps.
TRP Mission Control – CAN bus Ethanol Content With x3 Sensors x3 PWM Outputs
TRP also offer a input only box which has the ethanol content and x3 analog voltage inputs available
TRP ECA PLUS – CAN bus Ethanol Content Plus X3 Sensors - Universal
TRP Message format
For the Mission Control Box Auxiliary input/Outputs to work successfully there are two CAN packets involved, one sent from the ECU to the Mission Control Box and another that is sent back from Mission Control Box to the ecu. This may be subject to change or addition in future. For ease of input the diff file below has the base settings and custom maps to drive the outputs with a generic value. If you can wiring is correct and you plug the TRP box in it should start to operate, then you can tune the custom maps etc to suit the vehicle needs.
If you have updated ProECU after August 2026 the file about may not work and you will need to use these instead
- TRP Mission Control - Ethanol and analog Input x3 - PWM x3 Output Base Config File.ProECU67dot224onwards.erd
- TRP Mission Control - Ethanol and analog Input x3 - PWM x3 Output Base Config File.ProECU67dot224onwards.cal
In this file, the following have been configured
Inputs
CAN configuration set up for TRP box
Flex Fuel as CAN sensor (flexfuel hardcoded not calibrated)
CAN channels B, C & D as 0-5v inputs
CAN channel E as error status
Outputs
CAN output configured
Channel A configured to send the device type to the TRP box
Channel B, C & D configured to send the PWM frequency of 33Hz to Mission control
Boost control enabled and WG % output over CAN to PWM 1 (Channel D)
Custom map O set to output 10% to PWM 2 (Channel F) but not enabled
Custom map P set to output 10% to PWM 3 (Channel G)
If you don't want certain channels the custom maps can be disabled.
RaceROM Can Input (received by the ECU from the device)
Baud 500kb/s. DLC:8 11bit default ID 0x0E1. Recommend frequency 25 or 50hz
Byte 0 | Byte 1 | Byte 2 | Byte 3 | Byte 4 | Byte 5 | Byte 6 | Byte 7 |
Ethanol % | Analog Voltage 1 | Analog Voltage 2 | Analog Voltage 3 | Error Flag | |||
Byte | Name | Scaling |
0 | Ethanol Content (8 bit) | 1%/bit. |
1&2 | Analog Sensor 1 (16bit Lo byte first) | x 0.2046mV/bit. (0.0002046 V/bit). |
3&4 | Analog Sensor 2 (16bit Lo byte first) | x 0.2046mV/bit. (0.0002046 V/bit). |
5&6 | Analog Sensor 3 (16bit Lo byte first) | x 0.2046mV/bit. (0.0002046 V/bit). |
7 | Error Flags (8 bit) | 0 = good, non-zero indicates error. |
for inputs only use this diff file (universal can bus input box)
RaceROM CAN Output (sent from the ECU to the device)
Baud 500kb/s. 11bit ID Default ID 0x335 default 25Hz
Byte 0 | Byte 1 | Byte 2 | Byte 3 | Byte 4 | Byte 5 | Byte 6 | Byte 7 |
Version | PWM 1 frequency (Hz) | PWM 2 frequency (Hz) | PWM 3 frequency (Hz) | PWM Duty 1 % | PWM Duty 2 % | PWM Duty 3 % | future Output Bits |
Byte | Name | Scaling |
0 | Version (8 bits) | Fixed Value. Currently 0x25 (37 decimal). |
1 | PWM 1 Output Frequency (8 bit) | offset - 10Hz, 1 hz per bit (0 = 10hz 255 = 265hz) |
2 | PWM 2 Output Frequency (8 bit) | offset - 10Hz, 1 hz per bit (0 = 10hz 255 = 265hz) |
3 | PWM 3 Output Frequency (8 bit) | offset - 10Hz, 1 hz per bit (0 = 10hz 255 = 265hz) |
4 | PWM 1 Output duty (8 bit) Low-Side | x 2.55 (0.39215% per bit) |
5 | PWM 2 Output duty (8 bit) Low-Side | x 2.55 (0.39215% per bit) |
6 | PWM 3 Output duty (8 bit) High-Side H-bridge Push-Pull | x 2.55 (0.39215% per bit) |
7 | future outputs (8 bit) | MUST BE 0x00 1bit per output |
Reflex CAN Box
The Motiv reflex CAN expander can be utilized on the 370Z, it requires wiring in as per below and configuration using Motiv’s Nissan firmware. To use the reflex box you will need to configure the following. There is a diff file available with the following set up
CAN inputs configured
CAN output channel A identity byte
CAN Channel B Boost control WG duty (boost control willneed enabling)
CAN Channel C, CM O output set to 10% duty
CAN Channel D, custom input 1 set as switch
Supplementary data switched on
the diff file for this configuration is below,
RaceROM Can Input (received by the ECU from the device)
set the can input pre conifgured box
Byte 1 | Byte 2 | Byte 3 | Byte 4 | Byte 5 | Byte 6 | Byte 7 | Byte 8 | |
Version | Multiplex | Pulsewidth Actual | Fuel Pressure | Ethanol % | Aux Input | Error Flags | Checksum | |
Byte | Name | Scaling |
1 | Version (4 bits) Multiplex (4 bits) | Fixed value. Currently 0x11. |
2&3 | Pulsewidth Actual (16 bit big endian) | 0.01ms/bit. |
4 | Fuel Pressure (8 bit) | 10kPa/bit (0.1 bar/bit). |
5 | Ethanol Content (8 bit) | 1%/bit. |
6 | Aux Input (8 bit) | unscaled. |
7 | Error Flags (8 bit) | 0 = good, non-zero indicates error. |
8 | Checksum (8 bit) | CRC8 algorithm. |
RaceROM CAN Output (sent from the ECU to the device)
Baud 500kb/s. 11bit ID Default ID 0x335 default 25Hz
Byte 1 | Byte 2 | Byte 3 | Byte 4 | Byte 5 | Byte 6 | Byte 7 | Byte 8 |
Version 0x31 |
|
| Aux 1 PWM% | Aux 2 PWM % | Enable bit |
| |
Byte | Name | Scaling |
1 | Version (8 bits) | Fixed Value. Currently 0x31 (49 decimal). |
2 & 3 | Blank |
|
4 & 5 | Aux 1 PWM Output Frequency (16 bit big endian) | x 10 (0.1% per bit) Duty % |
6 | Aux 2 PWM Output Frequency (8 bit) | x 1 (1% per bit) Duty % |
7 | Digital Output enable | 0x00 off, greater than 0x00 on |
8 | Blank |
|
the reflex also utilizes an extra can packet to run the reflex box this is enabled by selecting the reflex supplementary TX packet option.
this supplementary packet sends out normal engine running data on the CAN Output ID for Reflex supplementary packet for use in the reflex box. This layout cannot be changed.
Byte 1 | Byte 2 | Byte 3 | Byte 4 | Byte 5 | Byte 6 | Byte 7 | Byte 8 |
Engine Speed (x1 + 0) | Throttle Angle (x10 +0) | Vehicle Speed (x1+0) | MAP (hPa) (x1000) | ||||