350Z/VQ35 ProECU OEM Maps and Strategies Guide

350Z/VQ35 ProECU OEM Maps and Strategies Guide

This article covers the control strategies and maps that are included by Nissan in the 350Z platform, these are features, functions or maps that are not controlled by RaceROM.

Accelerator and Throttle

The factory throttle maps are concave as shown in the factory calibration below.  By making these maps more linear the engine will deliver more power and torque for a given Accel pedal position. See where the modified map has been interpolated between 10% and 76% to produce a much more linear shaped curve, so for a given Accel pedal position the ECU will open the butterfly further. Note that this is only altering the Accel pedal output and doesn’t physically create any more power or torque!

there are different numbers and uses of maps depending on the generation, below is the accel pedal maps for, Gen1, gen2 and Gen3 (left to right). note that in the HR ROMs there are many more pedal scaling maps and the 370z style Throttle target max map is introduced

image-20260623-162249.png

The pedal scaling is the same for all generations, and the trustful map MUST match the normal map or a dtc will occur

image-20260623-162636.png

The throttle target MAX maps in the HR ecu will need adjustment as per the 370z

image-20260623-162923.png

CAM Timing

The VQ35 has gone through several iterations of cam timing set up

  1. the gen1 DE has intake cam VCT only with a fixed exhaust cam

  2. the gen2 DE rev up and Gen3 HR engine have both cams adjustable using a hydraulic Intake VTC controller and an electro magnetic retarder type exhaust cam controller

The intake cam control maps available will differ between platforms however the early gen ROMs appear to have some of the more advanced control strategies removed.

image-20260715-103025.png

the CAM control of both intake and exhaust cams are performed in closed loop, the Intake cam is primarily done with Proportional-Integral-Derivative (PID), the Exhaust com control can be done using either PID or Sliding Mode current Control (SMC).

You can select the type f feedback and the maps its uses for closed loop control, by checking the EVCT feedback type (PID or SMC) map, checked = SMC, unchecked = PID

image-20260715-111953.png

Intake CAM timing (Hydraulic Intake CAM control)

This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve. The ECM is calibrated to set a desired can angle target. Then, the ECM sends ON/OFF PWM signals to the intake valve timing control solenoid valve depending on the target and the error from target. This makes it possible to control the shut/open timing of the intake valve to increase engine torque in low/mid speed range and output in high-speed range.

image-20260715-095706.png

The cam control appears to use a typical Prop and derivative control system to correct for measured errors.

Due to only having one variably timed camshaft the map structure for gen1 DE is different to the gen2 & 3 cars, tuning the timing however is very similar.

image-20260715-093600.png

the base target map is the primary data to calibrate, the values are in cam advance from the 0 position

image-20260715-093922.png

there is a low temperature map that the VTC target interpolates between regular and cold map when coolant temperature lies between upper and lower thresholds

image-20260715-112831.png

If the cam timing is not staying on target because of worn cam gears adjustments can be made to the base duty and if the control is oscillating around the target the Prop and derivative gains for the oil control valve (OCV) can be tuned. The base duty for each bank is set by the Base duty, if the car has an oil temperature sensor the oil temp maps are used, if it doesn’t have a oil temp sensor then the normal maps are used.

After this the Prop and integral and derivative values are applied to the base setpoint to deliver the final duty.

Final duty = Base map + Prop map + (cam angle error x Integral gain) + derivative map

image-20260716-155634.png

 

Exhaust CAM timing (Electro Magnetic Exhaust CAM control)

image-20260715-112205.png

This camshaft control mechanism makes it possible to control the shut/open timing of the exhaust valve to increase engine torque and output in a range of high engine speed. the ECM sends PWM duty signals to the exhaust valve timing control magnet retarder depending on calibrated cam target. This is done in closed loop using the SMC method of feedback control by default, this can be changed if required by selecting the EVCT feedback type check box.

image-20260716-170752.png

checked = SMC control unchecked = PID control.

Exhaust CAM EVTC feedback by SMC control

this starts by calculating the real camp position and the angular velocity using, the real cam position is calculated by

Real Cam Position = measured cam angle * cam gear ratio map + Initial spring offset map

image-20260716-172837.png

the Duty Ratio for the cam control is set by the following formla

Duty = Duty conversion factor * SMC feedback control current

the SMC Feedback control current in amps is then calculated by

SMC Feedback control current = Linear control Factor + non linear control factor

the linear feedback factor is generated by the following principles (for each bank independently)

Linear feedback control factor = (Factor A + Factor B +Factor C +Factor D) / Gain

Factor A - linear control factor A * (target cam angle + Initial Spring offset)/Cam gear ratio

Factor B - linear control factor B * Cam angle error

Factor C - linear control factor C * Real Cam Position

Factor D - linear control factor D * Cam Angular velocity

image-20260716-175749.png

 

The non linear feedback factor uses

Non linear FB = (Non linear FB factor / linear gain) * non linear gain

Non linear FB factor= factor A * Cam error integral + factor B * real CAM position + factor C * Cam angular velocity

image-20260716-175814.png

Exhaust CAM EVTC feedback by PID control

If using the PID control the set up is the same as the PID control for the intake cam shaft.

350Z/VQ35 ProECU OEM Maps and Strategies Guide

DTCs

Diagnostic trouble codes are available for viewing

image-20260717-083740.png

Enables

there are bit switches in the OEM code that will switch on and off certain function inside the ECU, for example,

  • AT/MT Switch. sets the code for the torque control functions and other functions to include the automatic gearbox values in their calculations. this does not mean that if you swap the transmission type it will set everything up perfectly, other items may still need calibration

  • ASCD Button Enable - switches the code on to read the ADC and store it in ram to allow the ASCD input to be used on cars that don’t have cruise buttons natively.

  • NATS - used in engine swaps to allow engine starts in cars that are not in the correct nissan chassis.

Other enable bits are available but not defined as some of these functions can prevent functions from working correctly like the CAN Kline switches that change the comms method of the ECU.

Fueling

Fueling for the VQ35 is very similar to the VQ37 and VR38 but simpler where there are there is a main fuel map and other operating modes that can set alternative AFR target, such as high temperature or cat heating. The primary fuel target input is the 3D fuel target map that is naturally in equivalence ratio (% enrichment) but converted to an AFR target for ease of use.

There are separate function for cranking (done in raw Injector pulse width like GTR etc), injection angles, transient compensation and after start enrichment.

Live Data Parameters

  • AFR Sensor V (Volts)

  • Air Fuel Ratio (AFR) #1 - #2

  • Air Fuel Target (AFR)

  • Injector Pulse Width (ms)

  • Fuel Trim Short Term (%) #1 - #2

  • Fuel Trim Long Term (%) #1 - #2

  • O2 Sensor Bank #1 & #2 (gen1 RaceROM only)

Fuel Map (with RR use Fuel Map Mode1 to Mode 4) 

The fuel map contains target AFR based on Engine Speed (RPM) and Engine Load (%). The vehicle has two factory fitted wideband (narrow band on gen1) sensors (one for bank 1 and another for bank 2). The ECU uses Fuel Trim Short Term B1 and B2 to ensure the target AFR is achieved during light load closed loop. Further to this the Fuel Trim Long Term Bank 1 & 2 will make long term adaption trim for continuous Short Term Fuel Trim corrections.

When Engine Load increases the fuelling will operate in open loop and the FTST feedback will not work and the Target AFR will not necessarily be achieved.

EcuTek have replaced this factory Fuel Map with 4 new fuel maps that can be calibrated for each of the Map Switch Modes with RaceROM. Mode 1 is the default fuel map if Map Switching is not enabled.

image-20260717-084704.png

The Fuel Maps are an AFR Target, the ECU will generally strive to achieve a target AFR of 14.7 (or Lambda 1) during Closed Loop conditions. 

At higher load a more favourable AFR target is needed, at this point the fuelling will go Open Loop where there is no feedback control to the ECU to maintain the fuel target value. 

Closed loop will only work at light load.  The easiest indication of when closed loop is active is that Fuel Trim Short Term (FTST) are active.

During mid to full load the FTST will stop working and the ECU will operate in open loop.

Entering a value of less than 14.7 in the fuel map will force the ECU into Open Loop (FTST not working), this trick can be used on forced induction models with big injectors if you are struggling for Idle control and general Idle stability. 

Changing something simple like fuel pressure from say 3.0Bar to 4.0Bar would make the fuel table inaccurate, the FTST will compensate whilst in closed loop and this will transition into a negative Fuel Trim Long Term (FTLT) over a time period.

It’s important to understand that FTLT will be applied in Open Loop so it’s important that your FTST are tight and accurate or long term adaptation will mean that FTLT are applied on full load. This could make the engine run rich or lean over a long term. 

Long Term Fuel Trims can be cleared by using the ECU RESET under the Nissan GTR ECM Tool. They are also cleared after ECM programming.

EcuTek have converted the factory Nissan Lambda voltage into a more useful logging parameter called AFR Bank 1 and AFR Bank 2. These AFR logging parameters have been accurately scaled by EcuTek against two Innovate LM2 sensors, see the following screen shot below showing the calibration testing we made.

The factory sensors are quite accurate at richer AFRs but we still suggest that the values shown should only be used for indication and we strongly suggest that all AFR tuning is verified with a trusted standalone wideband sensor.

Be sure to check both Bank 1 and Bank 2, as they have different MAF scaling due to different air box designs. Also watch Fuel Trim Long Term and Fuel Trim Short Temp for bank 1 and 2.

Where different intakes are fitted the MAF scaling should be adjusted so that the FTST are between 90 and 110% at all times during closed loop.

OEM Fuel Injector Scaling (use RR instead)

The injector scaling works in a conventional manner, there are options for Injector Size, Voltage Multiplier and the Offset Time (ms). The standard Injectors are 302cc which are good for around 300bhp. The factory injectors are open at 84% at 7600rpm (305bhp) at 12.2:1 AFR. This means that factory injectors have a limited capacity for Ethanol tuning.  The factory Nissan GTR injectors (570cc) can make a good replacement for the 350z. The Injector Scaling and Offset values would need to be changed, here are the GTR settings.

For more information on scaling fuel injectors using the OEM method check out our article Scaling Injectors For Nissan Using OEM Method (GT-R, 370z)

Cranking Fuel maps

When using larger Injectors or running on Ethanol it becomes necessary to change the cranking fuel volume amount. There are numerous cranking fuel maps that are shown below, the Initial and step values are an open time period (ms) whereas the compensation maps are a % that affect the overall cranking and starting fuel volume amount.  The full control cannot be defined at this time but the results of changing the various cranking maps can be seen below.  The Cranking Fuel Injector Pulse Width #3 map shown below has been calibrated with 36ms and 96ms for the purpose of example. See on the left hand log file how the Injector pulse width (ms) reduces and decays much more quickly when compared to the right hand side where the Injector is open for a much longer period with higher values in the map.

The Cranking Fuel Compensation maps can be used as a global ‘compensation’ for the complete cranking period.  The next test results show the effect of adjusting the Cranking Fuel Injector Compensation #1 - #3

Fuel Enrichment

The hot and cold fuel map enrichment maps are used to trim the desired AFR by a percentage to attain the correct AFR for a given RPM and Engine Load.

Values above 100% will cause the engine to run Richer, (e.g. 110% will be 10% more fuel than desired) and values below 100% will cause the engine to run leaner. This map can be used to fine tune for larger Fuel Injectors without having to alter MAF scaling. 

NOTE: The Load Axis of the OEM map is limited to a load of 100% which makes the RaceROM maps better suited for MAF tuning.

Fuel Trim Per Cylinder

This map can be used to add extra fuel to certain cylinders, see the map help text for further information. We advise that the Injector Open Time is measured with an oscilloscope to ensure the correct Injector delivers the additional fuel, it appears that this map input axis shows cylinder numbers but it could be firing order.

2e00d88f-1ad9-45be-914f-bb727fa40064.png

Over Run Fuel Cut

There are a selection of cut types used in the 350z ecu, each different type of cut is initiated a different way depending on the calibration setting in the ecu, it appears that

Overrun fuel cut # 1 is in overrun with the idle flag on below 8km/hr

Overrun fuel cut # 2 is in overrun with the idle flag moves from off → on above 8km/hr

Automatic cars have a separate Lock up overrun control function on top of this other fuel cuts (SR control), this function is triggered when the TCM is in lockup or not and has a separate set of yet to be defined timers.

Over Run Fuel Cut#1

This is a type of cut that is set by the map value that is applied only under certain conditions, these are not typically achieved in normal operation.

Over Run Fuel Cut #1 & #2

The Engine Speed must be over this RPM for fuel injectors to be cut during a period of deceleration (lift off over run). Only the #2 maps are used during our testing.

Once entering fuel cut has ben set the are two timer before a full fuel cut is achieved, the first for a half cylinder cut the second is the timer to move to full fuel cut.

These timers can be seen in the map listing

image-20260721-092720.png

There are gear, vehicle speed and RPM thresholds for these types of cuts and a timer for going from no cut to half fuel cut and full cut that can be adjusted. these maps don’t usually need to be adjusted.

Over Run Fuel Cut Restore #1 & #2

This is the Engine Speed where the Fuel Injectors will be restored (turned on again). The Injector Open Time (ms) during overrun will never show zero and will be around 0.74ms, this is the Injector lag time period being shown but the injectors are not physically open. These values should always be at least 2300rpm above any target Idle speed (or the engine will stall on overrun). Raising these values to say 5000rpm when the coolant temp is hot will encourage pops and bangs during gear change and decal conditions. Only the #2 maps are used during our testing.

Transient Fueling

the transient fueling appear to be a simplified variant of what is in the GTR ROMs

https://ecutek.atlassian.net/wiki/x/MwDNAw

The strategy more basic with lest transient comp factors

image-20260721-153433.png

The wall wetting maps are smaller as is the air quantity map.

image-20260721-153357.png

The other transient comp maps (if they exist in the ROM) operate in roughly the same way.

AF Learning Range RPM - Load

These are the breakpoints for the adaptive Fuel Trim Long Term stored correction values that are learnt over time. These can be adjusted to help calibrate Fuel Trim more accurately during tuning. 

image-20260721-152343.png

Injection Angle

This shows the injector firing angle before TDC, these maps are the End of Injection (EOI), when running in sequential injection mode (as soon after start as i can get sync) it moves to the controlled end of injection strategy and calculates the start of injection based on the open time.

image-20260721-151832.png

the Injection Angle End 2 and Injection Angle Full Load 2 maps are the set point angle in crank degrees.

Fuel Cuts

Fuel cuts for rev limits or for overrun have a minimum duration to be applied, this can be adjusted by changing the Minimum Fuel Cut Duration.

image-20260721-164714.png

 

Fueling on Gen1 DE

There are some minor differences in the fueling strategy on gen1 350 DE, this is to do with the O2 sensing method differing, the control structures are mostly the same.

Idle Control

Idle control for the 350z engine is a slightly less advanced method as the GTR idle control where is does the throttle control based in l/min airflow using a learnt value as a base target and adders for ancillary load adders.

image-20260721-110408.png

for more information on idle control in Nissans please see the article, keep in mind that the 350z may not have all of the calibratable options defined unlike the GTR.

https://ecutek.atlassian.net/wiki/x/BQAZL

Gen 1 idle control is step more basic than the gen2/3 VQ engine but the main maps for target idle and feedback dead band are available.

image-20260721-110321.png

there are also Idle Ignition maps which are used when the vehicle goes into idle control mode, idle control mode is also active in overrun.

image-20260721-160910.png

Idle Ignition timing is calculated by adding the Idle Ignition timing Map #1/2/3/4 to the Idle Ignition timing Lean/Neutral/Stoich maps, and it is then limited to the calculated MBT. For example below the idle ignition 1 at 1600rpm and idle ignition lean at 60degC = 10 + 10 = 20deg which is less than the MBT at that RPM.

image-20260721-162224.png

Ignition timing (with RR use Fuel Map Mode1 to Mode 4)

The factory Nissan Ignition maps are low resolution and complex to understand. EcuTek have rewritten the Ignition control to provide 4 simple high resolution Ignition maps with real Ignition values for each map switch mode. The RaceROM Ignition maps offer extended RPM and extended engine load rescaling ability that’s critical for forced induction vehicles.

350Z/VQ35 ProECU RaceROM Supplement

Safe Mode - Safe mode is a term Nissan use when the ECU calculates that the knock retard is high enough to swap to the low octane maps, it also run different AFR and VTC target. This mode can also be set when things like a refueling even or DTC is detected. The parameter is loggable and Called Safe Mode.

Map List 

image-20260721-110958.png

Live Data Parameters

  • Ignition Timing (Deg) - the OEM logging parameter and the timing seen at the crank pulley

  • Ignition Timing Base (OEM) - The output of the either OEM or RR map lookup

  • Ignition Timing Compensation (RaceROM) - the output of the RaceROM compensation maps

  • Ignition Timing hooked value (RaceROM) - Ignition timing as its written to the ignition function

  • Ignition timing Overrun - The ignition timing calculated by the OEM overrun and Idle functions

  • Ignition timing RaceROM calc - the final RaceROM derived ignition timing (inc. corrections etc)

  • Kock Correction (Deg) - the current instantaneous knock retard

  • Knock Sensor Cylinder (1-6) - the knock sensor signal for each cylinder

  • Knock Threshold Cylinder (1-6) - the knock signal threshold value to register knock

Ignition Base Maps OEM (use RR Ignition instead)

See the comparison below showing the factory Ignition map filled with meaningless values vs the RaceROM high resolution Ignition map with Ignition Timing values.

image-20260721-111951.png

*** NOTE *** As the complex factory Ignition calculations have been over written and simplified by the RaceROM variant it’s important to calibrate the RaceROM Ignition maps accurately for your particular vehicle, the region of your vehicle and the fuel quality that is used.

If tuning the OEM strategies it is recommended that increases are added as an offset from the original map values. It is believed that it uses a calculated MBT timing which is then trimmed by the various maps for temperature range and estimated octane.

Knock Retard

The ‘Knock Control Enable’ maps which are used to enable and disable the knock control against RPM and Load. We suggest to enable the Knock Detection at high RPM so that the ECU can use active knock correction past 6000rpm as shown on the left in this screen shot below.

image-20260721-142427.png

With the standard knock switched off past 6000rpm the ECU will hold that knock retard to the rev limiter but if we allow knock detection to take place at high RPM then the ECU will build out any negative knock retard at high RPM (assuming the knocking has stopped).

There are limitations applied to how much knock retard can be applied at different load (BFS) and RPM break points

image-20260721-144616.png

The RPM/Load Area Advance limiter Hi / Low Octane are an abosolute value for knock retard (i.e. 9 = -9deg knock retard maximum).

The Knock Sensitivity map can also be altered to raise the knock threshold where the ECU will determine a knock retard value is required. Each row is a cylinder number and the values in the map are the threshold.

image-20260721-142228.png

Raising these maps by 5% (or maybe 10%) will make the ECU less sensitive to knock retard but you MUST always check for detonation with a  3rd party device.

RaceROM offers Per Cylinder Knock and Per Cylinder Knock Threshold logging ability to aid this calibration process and help identify noisy cylinders so the threshold can be raised without raising the other more quiet cylinders.

You can see in this example where cylinders 4 and 5 are making excessive noise and are breaking the threshold, this in turn is shown in the Ignition Correction parameter (green line) is producing more and more knock retard each time the threshold is breached.

Considerations should be made for logging speed that is available from the factory ECU, not every knock event can be shown in the sampling rate that’s available.

Note the central two cylinders 3 and 4 have higher thresholds due to these cylinders being more ‘noisy’ as they encased by cylinders 1, 2 and 5 and 6 in the V6 engine block design.

The Knock Retard Multipliers can also be increased and decreased to provide a global gain on the output of the knock sensors but as above you MUST ensure you check for detonation with det cans or a similar knock detection device.

Engine Cold/Warm Thresholds 

These parameters specify the Coolant temp thresholds for when the VTC Cam maps Cold or Warm should be used. The ECU will switch between the maps at 70deg Celsius.

Limiters

The 350z ECU has many sections of limiters some of which are undiscovered as yet, this section covers the limiter functions we have reverse engineered so far.

Brake On Switch Limits (BOS)

Brake on switch limiting is a function created as a safety limit so that accel pedal and brake cannot be applied at the same time. There are similar function in the GTR, 370z and even the VR30 ECU and the all apply a throttle target limit when the brake switch is applied with a vehicle speed threshold for enablement.

image-20260721-163138.png

NOTE: these maps are 1D values and are heavily number size limited so you cannot allow more than 28deg throttle when the brake switch is on. the accel threshold also cannot be adjust to not trigger above the number size limit of 28deg pedal.

The vehicle speed threshold can be adjusted so that it doesn’t trigger until a set speed

image-20260721-163306.png

Stationary No load Rev limit

The stationary no load rev limit is a safety feature to prevent the engine being help at high RPM for a long period of time, for example if the accel pedal was jammed wide open for a long time.

When the ECT is above the Stationary FC ECT threshold and the vehicle has no load applied to it.

image-20260721-164305.png

The ECU starts counting the number of revolutions at a rate set by the Stationary No Load Fuel Cut Activation counter step map values until the Stationary FC RPM counter value is hit.

image-20260721-164113.png

NOTE: if the RPM is below 2000 it will use the 1st value of the 2d map, so if setting at low RPM for stall converters you’ll need to set the 400rpm point to allow a count up)

image-20260721-164127.png

Once the counter has been hit the ecu then applies a fuel cut until the Stationary No Load Fuel Cut RPM is exceeded the fuel will be cut until the rpm drops below the Stationary No Load Fuel Cut Restore RPM value.

image-20260721-164515.png

This can be calibrated like a stationary rev limit/Launch Control if required.

Rev Limits (use RaceROM Per Gear Rev limit)

There are two types of Rev limits, the fuel cut and the throttle cut, the rev limit top two numbers are believed to be the rev limit activation threshold and then recovery threshold in forward gears and the bottom two in reverse

image-20260721-171615.png

The throttle cut rev limit is used to soften the fuel cut when approaching the rev limit.

image-20260721-171812.png

Speed Limits

There are two types of speed limit, a fuel cut type and a throttle cut type. to lift these limits you can increase the values in the maps to the required maximum speed.

image-20260722-161403.png

NOTE: On gen1 car the speed limit off throttle map is a hysteresis value for the on map, as opposed to the gen2/3 cars which have a set speed to recover from the speed limit.

Misc Limits

Calculated Load limit for OBD is a map used to limit what the the 100% load value is sent over the OBD logging. this map doesn’t usually need changing.

image-20260722-162845.png

Sensor scaling

Sensor scaling in 350z is again largely similar to the other Nissan models, the biggest missing sensor is that the 350z does NOT have a MAP sensor (manifold absolute pressure sensor) if relies solely on the MAF sensor. Extra sensors can be configured (MAP Fuel Pressure, Flex & O2 sensor) using the RaceROM sensors section, for more information on this see the RaceROM section.

350Z/VQ35 ProECU RaceROM Supplement

OEM sensors available to scale are

  • IAT, ECT, EOT (shared scale)

  • Throttle POsition

  • MAF sensor

The IAT and ECT and EOT sensors share the same scaling in the Coolant & IAT Sensor Scaling map

image-20260722-163535.png

Engine oil temperature has been labelled as in some gen2/3 ROM the oil sensor scaling is not shared.

Mass Airflow (MAF) sensor scaling is necessary for any upgraded intake, there are two minimum and one maximum voltage limits for the MAF sensor voltage range

image-20260722-164411.png

once the MAF voltage is read it is passed through the MAF scaling bank #1 (V to %) map which give a % of the maximum flow rate for the MAF tube. this map is what is used to adjust the airflow at different load ranges to correct the fueling.

image-20260722-164649.png

after the % of the maximum flow through the tube is found it is then multiplied by the MAF sensor (% to g/s) for load map

image-20260722-164810.png

this g/sec value is then passed to the airflow model and corrected, it is suggested that the MAF multiplier is used instead of this value as the MAF multiplier includes other corrections as its it added later in the calculation functions and gives a better multiped value.

the stock MAF tube is 66mm in diameter so a 76mm MAF should be 132% bigger than stock

(76mm^2 / 66mm^2) = 1.32

or the RR MAF multiplier set to 1.32.

BFS Multiplier

this value is what UPREV and other software use to do the MAF multiplication, we prefer not to use this unless we need to rescale the load to keep it below the number size limits on the load calculation.

image-20260723-085449.png

IF you need to reduce the load as its being capped by the number size limits you will need to scale this map down by a percentage (say 50%), then move the values of all of the maps with engine load as an axis to suit the new reduced (by 50%) load value to make sure that the looked up value references the new calculated value the same.

Throttle

the 350Z de and DE rev up have a single throttle body and MAF, where as the HR engine has twin throttle. If larger throttle bodies are fitted the throttle position scaling may need to be adjusted. this is once again done use the diameter squared.

The TPS Scale and TPS Scale Trustful must be identical other a DTC will occur

image-20260723-084654.png

The throttle control target has multiple input options, there are flags to swap the throttle target from using the torque calculations (to incorporate limits from the TCM traction control and limp modes). NOTE: this option should be used with caution as it may cause drivability issues.

image-20260723-085033.png

there are also limits in the accel pedal functions that prevent thr throttle from opening low in the rev range, these will usually not interfere with the driving but can be calibrated if required

image-20260723-085202.png

 

Overrun Throttle

During overrun when the idle flag is set but the RPM is high an airflow target is set using the learned base target and then the Decel Airflow Target Compensation map is applied to give the correct type of overrun throttle feeling.

image-20260720-110103.png

Torque

Nissans Torque control strategies on the VQ35 ecus is relatively simple compared to later vehicles, similar to the 370z they have a Torque Demand and Torque Demand - Trusful map that get referenced but different functions at different times, the first lookup is performed using the final accel pedal value converted to QHO using the TPS scaling maps engine speed and cubic capacity.

image-20260723-090217.png

This value generates a target engine torque which then gets passed through the torque arbitration functions, these include the Inverse torque filtering (if enabled) and anti jerk functions as well as all of the torque limits from the TCS, ABS system, gearbox and the other devices.

image-20260723-093152.png

the torque filtering can be enabled or disabled

image-20260723-093135.png
image-20260723-093102.png

This torque is also multiplied by the torque demand multiplier.

image-20260723-092703.png

This new limited value then gets passed though this map using a reverse lookup when it looks at the limited torque value at the current RPM and finds the correct QH0 value for that torque amount. this QH0 value is then limited and converted back into and Open area for the required airflow.

At this point the idle airflow and other correction open area’s are added in and then the throttle angle target is found by looking up the TPS scaling maps in reverse to get a target angle which the throttle then uses as a control target.

Torque Demand after multiplication is also sent out to the TCM etc and this is why it has been called a “line pressure” map as it increased the power train torque demand values received by these other modules. The Torque actual also contributes to the the response of external modules as both values are sent over can for modules to use. The Torque Actual map can be tuned to help with stead state setpoints of other modules as well.

image-20260723-092906.png

Radiator Fan Control

On the vehicle that use PWM radiator fans the radiator fan speed target can be adjust (as per the other Nissan platforms). The gen1 / early DE cars do not have the PWM fans and don not have these maps.

image-20260723-093327.png

these use vehicle speed and ECT thresholds in a 3D format to set a duty that the fan uses in the modes above.

image-20260723-093516.png

Gear Ratios

the gear ratios of in the ECU can be changed if the final drive has been changed for example

image-20260723-093611.png
image-20260723-094409.png